Saeed Bikass

Publikasjonar

• CFD estimation of a resistance coefficient for an egg-shaped geometric dome

  Domagala, Mariusz, Aga, Halvor Larsson, Bikass, Saeed, Momeni, Hassan, Stenfelt, Gloria Maria (2022)
  Applied Sciences 2022 Volum 12 ;(21)

• Treatment of oily legacy waste and defining future practices: Kuwait case study

  Bikass, Saeed, Al-Mulla, Mohammad, Al-Dhamen, Fahad, Prakash, Mishra Ved, Hadzalic, Zlatko, Handgraaf, Paul (2020)
  SPE International Conference and Exhibition on Health, Safety, Environment, and Sustainability 2020

• Fluid-Structure Interaction Simulation of Flow Control Valve

  Domagala, Mariusz, Momeni, Hassan, Domagala-Fabis, Joanna, Filo, Grzegorz, Amzin, Shokri, Bikass, Saeed (2020)
  Materials Research Proceedings (MRP) 2020 Volum 17 ;s. 36-42

• Life cycle assessment of low-temperature thermal desorption-based technologies for drill cuttings treatment

  Hu, Guangji, Liu, Huan, Rana, Anber, Li, Jianbing, Bikass, Saeed, Hewage, Kasun, Sadiq, Rehan (2020)
  Journal of Hazardous Materials 2020 Volum 401 ;

• Failure Prediction of Spool Control Valve using CFD Simulation

  Momeni, Hassan, Domagala, Mariusz, Bikass, Saeed (2020)
  Materials Research Proceedings (MRP) 2020

• Numerical Simulation of Fluid Flow inside the Flow Control Valve

  Domagala, Mariusz, Momeni, Hassan, Fabis-Domagała, Joanna, Krawczyk, Mariusz, Filo, Grzegorz, Bikass, Saeed (2019)
  Quality Production Improvement - QPI 2019 Volum 1 ;(1)s. 394-399

• Matrix FMEA Analysis of the Flow Control Valve

  Fabis-Domagala, Joanna, Momeni, Hassan, Domagala, Mariusz, Filo, Grzegorz, Bikass, Saeed, Lempa, Paweł (2019)
  Quality Production Improvement - QPI 2019 Volum 1 ;(1)s. 590-595

• From the Classroom to the Job Office: A Review on 3D Modelling and the Finite Element Method Analysis Teaching and Learning Method

  Bikass, Saeed, Momeni, Hassan (2016)

• From the classroom to the job office: A review on 3D modelling and the finite element method analysis teaching and learning method

  Momeni, Hassan, Bikass, Saeed (2016)

• From Environmental Hazard to Zero Impact

  (2015)

• Spray footprint effect on the induced distortion by the cooling process in the aluminum extrusion process

  Bikass, Saeed, Andersson, Bjørn, Pilipenko, Artem, Langtangen, Hans Petter (2013)
  Applied Thermal Engineering 2013 Volum 57 ;s. 14-23

• Simulation of initial cooling rate effect on the extrudate distortion in the aluminum extrusion process

  Bikass, Saeed, Andersson, Bjørn, Pilipenko, Artem, Langtangen, Hans Petter (2012)
  Applied Thermal Engineering 2012 Volum 40 ;s. 326-336

• Simulation of the distortion mechanisms due to non-uniform cooling in the aluminum extrusion process

  Bikass, Saeed, Andersson, Bjørn, Pilipenko, Artem, Langtangen, Hans Petter (2012)
  International Journal of Thermal Sciences 2012 Volum 52 ;s. 50-58

• Effect of length variation on distortion mode during cooling process in aluminum extrusion simulation

  Bikass, Saeed, Pilipenko, Artem (2011)

• Uncertainties on HTC measurement of water spray quenching of aluminum alloys

  Bikass, Saeed, Pilipenko, Artem (2011)

• Simulation of Distortion Mechanisms due to Non-Uniform Cooling in Aluminium Extrusion Process

  Bikass, Saeed, Pilipenko, Artem, Andersson, Bjørn, Langtangen, Hans Petter (2011)
  International Journal of Thermal Sciences 2011 Volum 52 ;s. 50-58

• Simulation of distortion due to non-uniform cooling in aluminium extrusion process

  Bikass, Saeed, Pilipenko, Artem (2010)
  International Journal of Material Forming 2010 Volum 3 ;s. 813-816