Saeed Bikass

Publications

• Investigating Wave Loads and Energy of a Spherical Object Using Numerical and Experimental Methods

  Erling Calvert Dolve, Saeed Bikass, Hassan Momeni, Mariusz Domagala, Bjørn Tore Hjertaker (2023)

• CFD estimation of a resistance coefficient for an egg-shaped geometric dome

  Mariusz Domagala, Halvor Larsson Aga, Saeed Bikass, Hassan Momeni, Gloria Maria Stenfelt (2022)
  Applied Sciences 2022 ;Volum 12.

• Treatment of oily legacy waste and defining future practices: Kuwait case study

  Saeed Bikass, Mohammad Al-Mulla, Fahad Al-Dhamen, Mishra Ved Prakash, Zlatko Hadzalic, Paul Handgraaf (2020)
  SPE International Conference and Exhibition on Health, Safety, Environment, and Sustainability 2020

• Life cycle assessment of low-temperature thermal desorption-based technologies for drill cuttings treatment

  Guangji Hu, Huan Liu, Anber Rana, Jianbing Li, Saeed Bikass, Kasun Hewage (2020)
  Journal of Hazardous Materials 2020 ;Volum 401.

• Failure Prediction of Spool Control Valve using CFD Simulation

  Hassan Momeni, Mariusz Domagala, Saeed Bikass (2020)
  Materials Research Proceedings (MRP) 2020

• Fluid-Structure Interaction Simulation of Flow Control Valve

  Mariusz Domagala, Hassan Momeni, Joanna Domagala-Fabis, Grzegorz Filo, Shokri Amzin, Saeed Bikass (2020)
  Materials Research Proceedings (MRP) 2020 ;Volum 17. s. 36-42

• Matrix FMEA Analysis of the Flow Control Valve

  Joanna Fabis-Domagala, Hassan Momeni, Mariusz Domagala, Grzegorz Filo, Saeed Bikass, Paweł Lempa (2019)
  Quality Production Improvement - QPI 2019 ;Volum 1. s. 590-595

• Numerical Simulation of Fluid Flow inside the Flow Control Valve

  Mariusz Domagala, Hassan Momeni, Joanna Fabis-Domagała, Mariusz Krawczyk, Grzegorz Filo, Saeed Bikass (2019)
  Quality Production Improvement - QPI 2019 ;Volum 1. s. 394-399

• From the classroom to the job office: A review on 3D modelling and the finite element method analysis teaching and learning method

  Hassan Momeni, Saeed Bikass (2016)

• From the Classroom to the Job Office: A Review on 3D Modelling and the Finite Element Method Analysis Teaching and Learning Method

  Saeed Bikass, Hassan Momeni (2016)

• From Environmental Hazard to Zero Impact

  Saeed Bikass (2015)

• Spray footprint effect on the induced distortion by the cooling process in the aluminum extrusion process

  Saeed Bikass, Bjørn Andersson, Artem Pilipenko, Hans Petter Langtangen (2013)
  Applied Thermal Engineering 2013 ;Volum 57. s. 14-23

• Simulation of initial cooling rate effect on the extrudate distortion in the aluminum extrusion process

  Saeed Bikass, Bjørn Andersson, Artem Pilipenko, Hans Petter Langtangen (2012)
  Applied Thermal Engineering 2012 ;Volum 40. s. 326-336

• Simulation of the distortion mechanisms due to non-uniform cooling in the aluminum extrusion process

  Saeed Bikass, Bjørn Andersson, Artem Pilipenko, Hans Petter Langtangen (2012)
  International Journal of Thermal Sciences 2012 ;Volum 52. s. 50-58

• Distortion Mechanisms due to the Cooling Process in Aluminum Extrusion

  Saeed Bikass, Bjørn Andersson, Artem Pilipenko, Xiang Ma (2012)

• Effect of length variation on distortion mode during cooling process in aluminum extrusion simulation

  Saeed Bikass, Artem Pilipenko (2011)

• Uncertainties on HTC measurement of water spray quenching of aluminum alloys

  Saeed Bikass, Artem Pilipenko (2011)

• Simulation of Distortion Mechanisms due to Non-Uniform Cooling in Aluminium Extrusion Process

  Saeed Bikass, Artem Pilipenko, Bjørn Andersson, Hans Petter Langtangen (2011)
  International Journal of Thermal Sciences 2011 ;Volum 52. s. 50-58

• Simulation of distortion due to non-uniform cooling in aluminium extrusion process

  Saeed Bikass, Artem Pilipenko (2010)
  International Journal of Material Forming 2010 ;Volum 3. s. 813-816